Enter Your Email Address To Subscribe Headend INFO !!!

New Service Insertion Teleste Luminato QAM

New Service Insertion Teleste QAM

Introduction

teleste lumato front

New Service Insertion Teleste QAM is very easy process in Teleste Luminato QAM. It is just drag and drop of service. There are basically three sections in UI of Luminato QAM shown below,

(1) Service Section

(2) Input Section

(3) Output Section

New Service Insertion Teleste QAM

We need to first add service in Input Section then drag from Input Section and drop to the Output Section. In this article we will see step by step process of New Service Insertion in Teleste Luminato QAM.

Step By Step New Service Insertion Teleste QAM

Step 1

First we need to add the access criteria for the service. click on the plus icon below shown in screen shot,

ECM ACCESS

Step 2

A new window will open we have given a example how to add service name i. e. COLORS and ECM ID , CW Group and Access Criteria. Then click apply.

ECM ACCESS CRIETARIA

Step 3

Now We need to first select the input method of service. Suppose you we are giving multicast input to GB1 port of QAM. Then add the Multicast IP of your service at GB1 port by clicking on “Plus” symbol as shown below in figure in red marked,

teleste luminato service insertion step 1

Step 4

A new window will open above this window you need to enter the Multicast IP or you can also select Unicast IP that depends upon your configuration. Now you need to select the Module. There are different modules available in the output side each module contains 4 Transport Stream. Now you need to select Quad we will select here first quad because we want to insert this service in first Transport Stream.

Now enter the IP address and port number then select the Gb port number weather it is Gb1 or Gb2. These Gb1 and Gb2 ports denotes the input port of your multicast IP. So we selected Gb1 because we are giving this multicast ip in Gb1 port as input. After that save it as shown below in the screen shot,

teleste luminato service insertion step 2

Step 5

Now you can see in the screen shot mentioned below we have found the service alias as “TEST cHANNEL” in the input side,

teleste luminato service insertion step 3

Step 6

We want to add this channel in first TS so we open the TS1 as shown in screen shot below,

teleste luminato service insertion step 4

Step 7

Now we selected the service “TEST cHANNEL” and drag it then drop it in the output side on TS 1,

teleste luminato service insertion step 5

Step 8

In the output side you can see the service alias “TEST cHANNEL” we open it and found our service inside it as shown below in screen shot named as TEN 2. In your case you can found it blank name of service. Now we will click on the gear icon near the service name.

teleste luminato service insertion step 6

Step 9

Now a new window will open to enable this service we need to click Enable Processing.

teleste luminato service insertion step 7

Step 10

Press Yes now.

teleste luminato service insertion step 8

Step 11

Now it is converting dynamic service into to static as shown below in screen shot,

teleste luminato service insertion step 9

Step 12

Now you need to give Output SID and service name. So now click in Advance Options then select “Service Type” as Digital Television Service. If you are passing radio service then you need to select radio service in this section. Now save it.

teleste luminato service insertion step 10

Step 13

In this scrambling tab you need to select the service for ECM. Here we are using gospell CAS. Then press apply.

teleste luminato service insertion step 11

Step 14

As you can see now below in the screen shot the ICON have changed of TEN 2 service and service is running now.

teleste luminato service insertion step 12

Conclusion

Thus teleste luminato qam GUI is very user friendly. To insert a new service in teleste luminato qam we need to first add the ECM for that service from input side then add the multicast for it. Then we need to follow the Drag and Drop function only to pass the service from input to the output section of the QAM.

Thus this is all about New Service Insertion Teleste QAM.

Know More About   Teleste Luminato QAM Overview

headend info

Facebooktwittergoogle_plusredditpinterestlinkedinmail



DOWNLOAD HEADEND INFO APP
headend info android app
  • Article By :
    Ujjwal Swami is Founder Of Headend INFO. He is a Entrepreneur and working for Cable Industry. He is also working for STB HD, Go For Tricks And Heterochromia Iridum Contact Admin@HeadendINFO.com Whatsapp No. +91 8239222444 (To Join Headend INFO Whatsapp Group Send Request On Above Number)

Comments

error: Want To Download These Articles ? Go To Books Tab !!!